Best Bi-Metal Hole Saw Kits for Steel and Sheet Metal (2026)

The kit to buy: Milwaukee Hole Dozer 49-22-4185, then Spyder and Diablo

Buy the Milwaukee Hole Dozer 49-22-4185 if one case has to cover the holes a home or small fab shop drills in mild steel, tube, steel studs and sheet-metal enclosures. Milwaukee lists 22 Hole Dozer bi-metal saws in this 28-piece kit, from 3/4 in. to 4-3/4 in. It adds three arbors, three 3-1/2 in. pilot bits and a 1/8 in. hex key. Milwaukee gives the saws a 3.5 TPI tooth design that it says offers ‘the longest life in metal applications’. Its warranty page covers Hole Dozer bi-metal saws under a Tooth Break Limited Lifetime Warranty. The kit wins on size count and on that written warranty. If every hole you drill is under 2-1/2 in., skip it: the ten saws from 2-5/8 in. up are dead weight for you.

Get Milwaukee Hole Dozer 49-22-4185

Buy the Spyder 601008 instead if most of your holes go into electrical boxes, panels and enclosures. Spyder’s 17-piece electrician kit holds 13 bi-metal saws. They cover every conduit knockout size from 7/8 in. to 4-1/8 in., plus 4-3/4 in. Its Rapid Core Eject arbor removes the slug without prying: press the button, pull back the hole saw and eject the core. Spyder’s own store lists the kit at $189.99. It is the wrong kit if you need 3/4 in., 1 in. or 1-1/2 in. holes, because none of those sizes is in the case.

Get Spyder 601008

Buy the Diablo DHS14SGP if your holes stop at 2-9/16 in. and you cut tube, stacked sheet or thick-wall stock. Diablo gives these bi-metal cups a 60 mm (2-3/8 in.) cutting depth, the deepest any of the three picks documents. All ten cups run on one Snap-Lock Plus mandrel with tool-free plug ejection. It is not the kit for large enclosure holes, because nothing in the case cuts a 3 in., 3-5/8 in. or 4-1/8 in. knockout.

Get Diablo DHS14SGP

These picks were not tested. The ranking comes from what each maker’s specifications show. Each kit had to pass four tests on its maker’s own documentation:

All three pass. Cut depth, size range above 2-1/2 in., core removal and warranty decide between them. Nobody whose main job is stainless steel should buy any of the three; the last section covers why.

Milwaukee Hole Dozer 49-22-4185: 22 saws and a tooth-break warranty

Ten of Milwaukee’s 22 saws are 2-5/8 in. or larger: 2-5/8, 3, 3-1/4, 3-3/8, 3-5/8, 3-3/4, 4-1/8, 4-1/4, 4-1/2 and 4-3/4 in. The kit also has every conduit knockout size from 7/8 in. to 4-1/8 in.: 7/8, 1-1/8, 1-3/8, 1-3/4, 2, 2-1/2, 3, 3-5/8 and 4-1/8 in. So it does the same box work as the Spyder kit and adds the general fabrication sizes a shop needs for grommets, bulkhead fittings, vent holes and tube notches.

Milwaukee’s includes list gives one 3/8 in. hex shank arbor, one 7/16 in. hex shank arbor and one 7/16 in. No Wobble arbor, plus three 3-1/2 in. pilot bits. The 3/8 in. hex arbor fits a 3/8 in. drill chuck. The two 7/16 in. arbors need a 1/2 in. chuck, and a 4-3/4 in. saw belongs in a 1/2 in. drill on low gear anyway. Milwaukee’s kit page text gives no cutting depth or hub thread size; its pages for single Hole Dozer bi-metal saws (49-56-0062, 49-56-9646) list a 1-5/8 in. cutting depth. The cup decides whether a deep pass works, so if you need a documented depth, Diablo’s 2-3/8 in. is the figure to use.

Milwaukee’s tooth figure is 3.5 TPI, which puts about 0.29 in. between teeth. A coarse pitch suits thick-wall tube and 3/16 in. or 1/4 in. flat bar, where each tooth takes a real bite. Thin sheet is its weak spot. 18-gauge steel is about 0.048 in. thick, so less than one tooth is in the cut at any moment, and a single tooth can catch the edge and spin the work. Clamp the sheet, back it with scrap plywood and ease the feed as the teeth break through. Milwaukee’s page for its 1-1/4 in. Hole Dozer bi-metal saw (49-56-0062) lists ‘thick/thin metals, aluminum, drywall, plastics, wood, wood with nails’ as its applications.

Milwaukee’s warranty page covers Hole Dozer bi-metal saws under a Tooth Break Limited Lifetime Warranty and excludes the Hole Dozer with Carbide Teeth line. On a large-diameter saw, a stripped tooth is the costly failure. Milwaukee’s term covers tooth breakage or fracture caused by defects in material or workmanship under normal use, for the original purchaser from an authorized Milwaukee distributor. It does not apply to damage from misuse, alterations, abuse or normal wear and tear. It is not worth the money if you only drill 7/8 in. and 1-1/8 in. holes in boxes. Milwaukee sells single Hole Dozer saws, such as the 4-1/8 in. 49-56-9646, so you can buy only the sizes you use.

Spyder 601008: the enclosure kit with button core ejection

Spyder lists 13 bi-metal saws in the 601008: 7/8, 1-1/8, 1-3/8, 1-3/4, 2, 2-1/4, 2-1/2, 2-5/8, 3, 3-1/4, 3-5/8, 4-1/8 and 4-3/4 in. The other four pieces are Hex8 and Hex10 arbors with matching high speed steel pilot bits. Spyder says to use a pilot bit correctly sized for the hole saw and to make sure it extends beyond the cutting edge of the saw by at least 1/4 in. Spyder’s catalog defines Hex8 as a 3/8 in. hex shank and Hex10 as a 1/2 in. hex shank. The small arbor fits a 3/8 in. chuck, and the large one needs a 1/2 in. chuck. Spyder’s material list for the kit includes steel and metal, stainless steel, cast iron and sheet metal. Spyder says to drill only materials listed on the product label. It gives the depth of cut as 1-7/8 in.

The Rapid Core Eject arbor is the reason to pay for this kit. Spyder describes the cycle as ‘drill hole, press button, pull back the hole saw, and eject the core’. In steel, the slug from a 1-3/8 in. hole in a 16-gauge box wedges tight in the cup. Without ejection you pry it out with a screwdriver through the cup’s side holes, once per hole. On a panel with twenty knockouts, the button saves that job twenty times. Spyder warns not to use the saws near flammable materials or gases, and to check the work area for hidden gas pipes, electrical wires and water pipes before blind or plunge cuts.

Spyder against Milwaukee: Spyder wins if you drill boxes and panels all day, because of the core ejection and a case built around knockout sizes. Milwaukee wins for a mixed shop. It has 22 saws against Spyder’s 13, includes 3/4 in. at the small end, and is covered by a written tooth-break warranty. Both kits cover 7/8 in. through 4-1/8 in. and 4-3/4 in. Neither has a size gap in conduit work.

Skip the Spyder kit if your general fab work needs 3/4 in., 1 in. or 1-1/2 in. holes for grommets, axles or pipe. Spyder includes none of those three, and adding single saws to a $189.99 kit (Spyder’s own store price) undoes its value.

Diablo DHS14SGP: deepest cups, one mandrel, sizes to 2-9/16 in.

Diablo lists the DHS14SGP as ten bi-metal hole saw cups, one Snap-Lock Plus mandrel, one pilot bit and two adaptor nuts. MSC’s listing for the set gives the ten cups as 7/8, 1, 1-1/8, 1-3/8, 1-1/2, 1-3/4, 2, 2-1/8, 2-1/2 and 2-9/16 in. Diablo says the cups drill wood, plastic, aluminum, metal and stainless steel, and lists steel and steel studs among the materials they cut. The 1 in. and 1-1/2 in. cups are the general sizes the Spyder kit leaves out.

Depth is where Diablo wins. Its figure is 60 mm (2-3/8 in.) of cutting depth, against Spyder’s 1-7/8 in. That difference decides tube work. A 2 in. square tube needs more than 2 in. of cup to go through both walls in one pass. The Diablo cups clear that; the Spyder cups stop at 1-7/8 in. and do not. The same applies to two 1 in. flanges clamped together, or a stack of sheet blanks drilled as one.

Diablo says the Snap-Lock Plus mandrel fits all Diablo hole saws from 5/8 in. to 6 in. diameter, with tool-free plug ejection. One mandrel for every cup means no second arbor to find when you jump from 7/8 in. to 2-1/2 in. If you later need a 3 in. or 4-1/8 in. hole, a single Diablo cup in that size fits the mandrel you already own.

Diablo against Milwaukee: Diablo wins on documented depth and a single mandrel. Milwaukee wins as soon as your work goes past 2-9/16 in. Buying the 3, 3-5/8 and 4-1/8 in. cups one at a time to bring the Diablo set up to Milwaukee’s range is the wrong way to spend the money. If you know you need those sizes, start with the Milwaukee kit.

Lenox, DeWalt, HYCHIKA and Amazon Basics: what each gives up

The Lenox Electrician Hole Saw Kit (17 pc.), part 308021200L, is another electrician’s kit to weigh against Milwaukee. Lenox lists 3/4, 7/8, 1-1/8, 1-3/8, 1-3/4, 2, 2-1/2, 2-11/16, 3, 3-5/8, 4-1/8 and 4-3/4 in. saws, with 2L and 5L arbors. Lenox says the saws fit both quick-change and traditional non-quick-change arbors. Lenox also claims up to 50% longer life, measured against its previous-generation bi-metal hole saw drilling low carbon steel, not against other brands. Lenox’s own page for this kit says it is not eligible for any warranty. Milwaukee covers more sizes (22 against 12) under a written tooth-break warranty, so Milwaukee wins. Lenox’s page lists its dealers under Where to Buy.

DeWalt’s catalog lists the D180001 as a 9-piece plumber’s kit: 3/4, 7/8, 1-1/8, 1-1/2, 1-3/4 and 2-1/4 in. saws, plus a 1/4 in. mandrel, a 7/16 in. Quick Change mandrel and a replacement parts set. It has no 1-3/8 in., 2 in. or 2-1/2 in. saw. That misses the knockouts for 1 in., 1-1/2 in. and 2 in. conduit, so for steel boxes the Diablo set does more.

HYCHIKA’s 17-piece bi-metal kit is a budget alternative to these. HYCHIKA’s product copy lists eleven saws from 19 mm to 68 mm (3/4 in. to about 2-11/16 in.), two mandrels, three drill bits and a hex key. It gives the maximum cutting depth as 40 mm, about 1-9/16 in. HYCHIKA lists its suitable materials as soft metal, wood, PVC, plastic and gypsum board, and says it suits soft metals including thin steel sheet. HYCHIKA’s own store lists it at $49.99. That is far less than Spyder’s $189.99 for its kit, which is what you gain. You give up 20 mm of depth against Diablo’s 60 mm, every size above 68 mm, and a tooth-break warranty like Milwaukee’s; HYCHIKA’s own store lists a 365-Day Warranty without stating tooth-break cover.

Amazon Basics sells a 9-piece bi-metal kit. Its listing gives six saws from 25/32 in. to 2-11/16 in., two hex arbors with pilot drills and a hex key, for metal, plastic and plasterboard. Six saws leave gaps between the knockout sizes, and it stops below 3 in. It fits a homeowner who needs a few holes in light sheet, not a shop.

Sizes, chucks and speed: matching the kit to your drill

In a steel shop, knockout sizes are the hole sizes most worth owning, because boxes, panels and connectors are built around them. Greenlee’s knockout charts give these conduit-to-hole sizes:

Milwaukee and Spyder cover the whole list. Diablo stops after 2-1/2 in. HYCHIKA’s metric range reaches 68 mm, past 2-1/2 in., but the 3 in. through 4-1/8 in. sizes are beyond it.

Match the arbor shank to your chuck before buying. A 3/8 in. cordless drill takes Milwaukee’s 3/8 in. hex arbor and Spyder’s Hex8. Milwaukee’s 7/16 in. arbors and Spyder’s Hex10 (1/2 in. hex) need a 1/2 in. chuck. If your shop drill has a 3/8 in. chuck, you can use Milwaukee’s small arbor but not its large ones.

Always wear eye protection; Spyder also calls for a dust mask, non-skid safety shoes, protective apparel and hearing protection in appropriate conditions. Speed scales with diameter. Each revolution, the rim of a 4-3/4 in. saw covers about 14.9 in., against about 2.7 in. for a 7/8 in. saw, which is 5.4 times as far. If both run at the same RPM, the large saw’s teeth move 5.4 times faster through the steel and overheat. Run the large saws on the drill’s low gear and the small ones faster. Spyder says to always drill using a drill motor that is equipped with a support handle, and to start cutting with a light forward pressure. Use cutting oil in steel, and back off as soon as the chips turn blue. Spyder warns that hole saws are not to be used in hammer or impact mode: only drill in standard rotary drilling mode.

Spyder’s kit page says to read the Spyder Hole Saw RPM Chart for the recommended operating speed for the saw size and the material being cut. Diameter, material and the color of the chips set the speed: a slow, steady curl of chips is right, and smoke or blue chips mean slow down.

Where bi-metal stops: plate, stainless and carbide

Cup depth rarely limits flat plate. Spyder’s 1-7/8 in. and Diablo’s 2-3/8 in. are both many times deeper than 1/4 in. or 3/8 in. plate. The limit is heat at the tooth tips. Spyder says to check before each use that the hole saw is free from damage and excessive wear, and to discard it if damage is noticed or suspected. Bi-metal teeth soften when a large saw runs too fast in thick mild steel, and the teeth you dull on one 4 in. hole in 3/8 in. plate are the ones a box job needed. For regular holes in plate thicker than 1/4 in., a bi-metal kit is the wrong tool. An annular cutter in a magnetic drill is the shop answer, and it is a different purchase.

Stainless steel is where bi-metal loses money fastest. It work-hardens when a tooth rubs instead of cutting, and a dulled bi-metal saw then glazes the surface rather than cutting through it. Diablo and Spyder both list stainless among the materials their cups cut, which covers the occasional hole. If stainless is regular work, Milwaukee’s answer is a different kit, the 12 PC Hole Dozer with Carbide Teeth, 49-22-3090. Milwaukee says its 3 TPI carbide teeth cut stainless steel and cast iron. It is a carbide-tooth kit, not a bi-metal one, and Milwaukee’s warranty page excludes the carbide-teeth line from the bi-metal Tooth Break Limited Lifetime Warranty.

Thin sheet is the opposite problem. Under 20 gauge (about 0.036 in.), any hole saw tends to grab and leave a burr-rimmed, slightly oval hole. For a few holes in thin panel, a step drill or a knockout punch leaves a cleaner edge. A hole saw kit earns its place in the 16- to 10-gauge range of boxes, studs and brackets, and in tube.

FAQ

What size hole saw do I need for 1/2 in. conduit in a steel box?

7/8 in. Greenlee’s knockout charts size the hole for 1/2 in. conduit at 7/8 in., 3/4 in. conduit at 1-1/8 in. and 1 in. conduit at 1-3/8 in. The Milwaukee 49-22-4185, Spyder 601008 and Diablo DHS14SGP all include all three sizes.

Will a bi-metal hole saw kit cut 1/4 in. steel plate?

Yes, for occasional holes. Run low RPM, use cutting oil and keep a steady feed. Spyder gives its cups 1-7/8 in. of cutting depth and Diablo gives its cups 2-3/8 in., so depth is not the limit; heat at the teeth is. For regular holes in plate of that thickness, an annular cutter on a magnetic drill lasts far longer than bi-metal teeth.

Which of these kits has a warranty on the teeth?

Milwaukee covers Hole Dozer bi-metal saws, including those in the 49-22-4185 kit, under a Tooth Break Limited Lifetime Warranty. Its carbide-teeth Hole Dozer line is excluded. Lenox’s page for its 308021200L electrician kit says that kit is not eligible for any warranty.