Best Lincoln, Miller and Hobart Welders: The One to Buy from Each

Lincoln, Miller and Hobart all make good welders. The real question is which model to buy from each. Here is one pick per brand for 120V MIG, dual-voltage MIG and multi-process work, plus the one welder most readers should buy.

The short answer: buy the Hobart Handler 210i

The Hobart Handler 210i is the overall pick. The criteria were: it runs on both 120V and 240V, it welds the full range of home-shop steel, it is light enough to carry, it has a long warranty, and it has the lowest listed price of the three dual-voltage MIG picks. Hobart rates it for 24 gauge to 3/8 in. mild steel and 210 A at 25% duty cycle on 240V. It weighs 26 lb, and its 5/3/1 warranty covers transformers, stabilizers and main rectifiers for five years. Hobart lists it at about $1,000. That is less than Miller lists its 120V-only Millermatic 142.

Get Hobart Handler 210i

Who should buy something else: if you will weld long beads on a 120V outlet, the 210i is rated for only 90 A at 25% duty cycle on a 20 A circuit, so the Lincoln POWER MIG 211i or Millermatic 211 PRO below suits you better. If you need TIG or stick, skip to the multi-process picks.

The one to buy from each brand

JobLincolnMillerHobart
120V MIGLincoln Easy MIG 140Miller Millermatic 142 (winner)Hobart Handler 140EZ
Dual-voltage MIGLincoln POWER MIG 211iMiller Millermatic 211 PROHobart Handler 210i (overall pick)
Multi-processLincoln POWER MIG 215 MPiMiller Multimatic 215 PRO (winner)Hobart Multi-Handler 200

For AC TIG on aluminum, the one machine here is the Miller Multimatic 220 AC/DC, covered after the multi-process picks.

These picks were not tested. They come from each maker’s product page and spec sheet. Every machine was judged on the same points: rated output and duty cycle at the input voltage you will actually use, the steel thickness the maker states, weight, what comes in the box, the warranty, and the maker’s listed price where the maker gives one.

A note for readers of older comparisons: the makers have moved on. Hobart’s current Handler line is the 125, 140EZ and 210i, and the Handler 210MVP no longer appears in it. Lincoln marks the POWER MIG 210 MP as discontinued and says the POWER MIG 215 MPi replaces it. Miller’s Millermatic line now lists the 211 PRO rather than the earlier 211. The picks here are current models.

120V MIG: the one to buy from each brand

A 120V MIG welder plugs into a household outlet and covers sheet metal, brackets, carts and light repair. All three brands make a 140 A machine. On paper they are not equal.

Miller Millermatic 142: the best 120V MIG of the three

The Miller Millermatic 142 wins this class on duty cycle and weight. Miller rates it at 100 A at 19 V and 60% duty cycle, and 80 A at 100%. That is twice the duty cycle of the Hobart’s rating, at a higher current. It weighs 33 lb, welds 24 gauge to 3/16 in. mild steel in a single pass, and has Auto-Set: you set wire diameter and material thickness, and the machine sets the parameters. Miller says it gives full output on a generator of 5,000 watts or more. A 10 ft MDX-100 gun and a gas regulator come in the box. Miller’s warranty is three years parts and labor on the welder and 90 days on the gun. Miller lists it at about $1,140.

Get Miller Millermatic 142

Hobart Handler 140EZ: Hobart’s 120V pick

The Hobart Handler 140EZ is rated at 90 A at 18.5 VDC and 30% duty cycle, with a 30-140 A range and 24 gauge to 3/16 in. on mild steel. EZ Mode sets the machine from a turn of each knob. It has a cast aluminum wire drive and takes 4 or 8 in. spools, and Hobart’s SpoolRunner 150 spool gun plugs in for 18-14 gauge aluminum (sold separately). It weighs 53 lb, 20 lb more than the Millermatic 142. Hobart says it is not recommended for use with engine-driven welders or standalone generators, so buy the Miller if you weld off a generator. Buy the Handler 140EZ if you want Hobart’s 5/3/1 warranty, which includes one year on the gun against Miller’s 90 days.

Get Hobart Handler 140EZ

Lincoln Easy MIG 140: Lincoln’s 120V pick

The Lincoln Easy MIG 140 is a plain machine: two knobs (wire speed and voltage), a metal case, and a brass-to-brass gun connection. Lincoln lists a 30-140 A output, a 20% duty cycle, a weldable range of 24 gauge to 5/16 in. and a weight of 50 lb, with a three-year warranty. Lincoln’s product page carries a California Proposition 65 warning: cancer and reproductive harm. The 20% duty cycle is the lowest of the three 120V picks. That is the reason to pass on it unless you want a plain two-knob machine or already run Lincoln’s Magnum PRO 100SG spool gun, which it accepts.

Get Lincoln Easy MIG 140

Dual-voltage MIG: the one to buy from each brand

A dual-voltage MIG welder runs on a 120V outlet now and a 240V circuit later, and on 240V Hobart and Miller rate their dual-voltage picks for steel up to 3/8 in. For most buyers this is the class to buy in, which is why the overall pick comes from it.

Hobart Handler 210i: the overall pick

The case for the Hobart Handler 210i is above. In short: 30-210 A on 240V, rated 210 A at 24.5 VDC and 25% duty cycle, 24 gauge to 3/8 in. mild steel, 26 lb, and a listed price of about $1,000. It has a Quick Select drive roll, a cast aluminum wire drive, and a built-in gas solenoid with a dual-gauge regulator in the box. It is spool gun ready for aluminum with the SpoolRunner 100. Hobart says it gives full output from a generator with 9,500 watts continuous on 240V. Its weak point is 120V use. On a 15 A circuit Hobart rates it for 45 A at 100% duty cycle, and on a 20 A circuit for 90 A at 25%.

Get Hobart Handler 210i

Miller Millermatic 211 PRO: buy it for long welds and pulsed MIG

The Miller Millermatic 211 PRO is the machine to buy if you weld long seams or a lot of aluminum and thin sheet. Miller rates it at 160 A at 22 VDC and 60% duty cycle on 240V, and 215 A at 30%. On 120V it is rated 110 A at 60%. Both are far longer duty cycles than the Hobart’s. It adds Auto-Set, Dyna-Pulse pulsed MIG (Miller says it lowers heat input on thin material and cuts spatter), BeadVision graphic feedback, USB software updates and a 15 ft gun. Miller rates it for steel and aluminum to 3/8 in. It weighs 35 lb, and Miller lists it at about $1,700, roughly $700 more than the Handler 210i. That is the price of the duty cycle and the pulse.

Get Miller Millermatic 211 PRO

Lincoln POWER MIG 211i: buy it if you weld mostly on 120V

The Lincoln POWER MIG 211i is Lincoln’s current dual-voltage MIG welder. Lincoln says it is replacing the POWER MIG 180 Dual. Lincoln rates it at 95 A at 18.8 V and 60% duty cycle on 120V, which is a much longer run on a household circuit than the Hobart’s 90 A at 25%. On 230V it is rated 175 A at 22.8 V and 30%, with a 20-211 A range. It has a seven-segment display, basic knobs, a three-step setup and a Magnum PRO 100L gun. It weighs 41 lb and carries a three-year warranty. Lincoln’s product page carries a California Proposition 65 warning: cancer and reproductive harm. Lincoln’s MSRP is about $1,600. It beats the Hobart on 120V. The Millermatic 211 PRO rates higher still on 120V (110 A at 60%) for about $100 more by the two makers’ list prices. Buy the 211i if your shop will stay on 120V for a while and you want a Lincoln. If you have 240V, the Hobart does more for less.

Get Lincoln POWER MIG 211i

Multi-process: the one to buy from each brand

A multi-process machine adds stick and DC TIG to MIG. Stick handles rusty farm steel and wind. TIG handles thin stainless and precise work.

Miller Multimatic 215 PRO: the best multi-process of the three

The Miller Multimatic 215 PRO is the only one of the three rated for MIG at 60% duty cycle (160 A on 240V, 110 A on 120V; Hobart and Lincoln publish 30%, 40% and 100% figures instead), and it wins on weight (35 lb, the lightest of the three) and on the number of processes: MIG, pulsed MIG, flux-cored, DC TIG, pulsed TIG and DC stick. It also has Auto-Set and gas detection. Miller rates it for 24 gauge to 3/8 in. steel with MIG and 24 gauge to 1/4 in. with TIG, and gives 190 A at 20% duty cycle for TIG and for stick on 240V. Miller lists it at about $2,125. Two catches: the base package has no TIG torch, and Miller does not recommend it for 6010 stick electrodes.

Get Miller Multimatic 215 PRO

Hobart Multi-Handler 200: buy it if you want TIG in the box

The Hobart Multi-Handler 200 does MIG, flux-cored, DC TIG and stick on 120V or 240V. It comes with a 12.5 ft TIG torch, tungsten and collets, which the base Multimatic 215 PRO and POWER MIG 215 MPi packages do not include (both makers sell TIG-kit bundles at extra cost). Hobart rates it at 165 A at 30% duty cycle for MIG and TIG on 240V, and 140 A at 30% for stick, with 24 gauge to 3/8 in. for MIG and 22 gauge to 3/16 in. for TIG. It weighs 38.4 lb and carries the 5/3/1 warranty. The foot control is sold separately, and Hobart does not recommend it for 6010 electrodes. Hobart does not list a price, so the price varies by seller.

Get Hobart Multi-Handler 200

Lincoln POWER MIG 215 MPi: Lincoln’s multi-process pick

The Lincoln POWER MIG 215 MPi is rated 215 A at 24.8 V and 30% duty cycle for MIG on 230V, and 120 A at 100%. TIG and stick are each rated 175 A at 30%. Lincoln builds in a TIG solenoid and a foot pedal adapter, and adds Ready.Set.Weld setup, ArcFX visual feedback on settings, and memory. Lincoln’s product page carries a California Proposition 65 warning: cancer and reproductive harm. It weighs 48 lb, has a three-year warranty, and Lincoln’s MSRP is about $2,250. The TIG torch is sold separately. By the two makers’ list prices it costs more than the Multimatic 215 PRO, and it weighs 13 lb more. Buy it if you want a Lincoln multi-process machine with saved settings, or if your 230V MIG work runs long at moderate current. Lincoln’s 120 A at 100% duty cycle on 230V (and 80 A at 100% on 120V) are the only 100% MIG ratings the three multi-process picks publish.

Get Lincoln POWER MIG 215 MPi

Miller Multimatic 220 AC/DC: only if you will TIG aluminum

None of the picks above does AC TIG, and aluminum TIG needs it. The Miller Multimatic 220 AC/DC adds AC TIG with AC balance from 60-80% and frequency from 60-150 Hz. It has high-frequency starts, and Miller says it runs E6010 stick electrodes. It comes with a TIG torch and an RFCS-14 HD foot control. On 240V Miller rates it at 210 A at 20% for TIG and 170 A at 40% for MIG. It weighs 56 lb, and the warranty is three years parts and labor, with 90 days on the gun. Miller lists it at about $4,285, about twice the Multimatic 215 PRO. If you will not TIG aluminum, that money is wasted.

Get Miller Multimatic 220 AC/DC

Who owns Hobart, and does it matter?

Miller and Hobart are both ITW brands. Hobart’s spec sheets read “Hobart Welding Products … An ITW Welding Company” and state that Hobart and the Hobart logo are trademarks of Illinois Tool Works, Inc. Miller’s spec sheets carry the same line for Miller Electric Mfg. LLC. ITW Welding’s US site lists Miller and Hobart Welding Products among its brands, with Hobart Brothers Company at Troy, Ohio and Miller Electric at Appleton, Wisconsin. Lincoln Electric is not part of ITW. Lincoln says it was founded on December 5, 1895, in Cleveland, Ohio.

What the shared parent means for a buyer:

Which brand should you buy?

Buy Hobart if you want the most welder for the money on a dual-voltage MIG. The Handler 210i is the lightest and lowest-listed of the three dual-voltage picks, and its warranty runs longest on the main power components. Its Multi-Handler 200 is also the only one of the three multi-process picks with a TIG torch in the box. Do not buy Hobart if you weld long beads on 120V, or if you need AC TIG.

Buy Miller if duty cycle, pulsed MIG or aluminum matter to you. Miller rates the Millermatic 142 at 100 A at 60% duty cycle, and the Millermatic 211 PRO and Multimatic 215 PRO at 160 A at 60% on 240V. No other pick here publishes a 60% rating that high in its class. Miller also makes the only AC TIG multi-process machine on this page. In dual-voltage MIG you pay for it: the 211 PRO lists at about $1,700 against about $1,000 for the Handler 210i. In multi-process, Miller’s list price is the lower of the two makers that publish one.

Buy Lincoln if you already own Lincoln accessories. Lincoln lists its Magnum PRO 100SG spool gun as an option for all three Lincoln picks. On the makers’ published figures, though, Lincoln does not win a class here. The POWER MIG 211i rates better than the Hobart on 120V (95 A at 60%), but the Millermatic 211 PRO rates higher still. Lincoln’s 120V-only Easy MIG 140, with its 20% duty cycle, is the weakest of the 120V picks.

What is not worth the money

Before you buy: power, plugs and generators

Check the outlet before you choose the model. The Handler 210i’s 120V ratings depend on the circuit: Hobart gives 45 A at 100% duty cycle on a 15 A circuit and 90 A at 25% on a 20 A circuit. Hobart ships the Multi-Handler 200 with 5-15P (120 V, 15 A) and 6-50P (240 V, 50 A) plugs. Miller ships the Multimatic 220 AC/DC with 5-15P and 6-50P plugs and sells the 5-20P plug separately.

If you weld off a generator, the makers state the minimum. Miller gives 5,000 watts for full output from the Millermatic 142 and 10,000 watts for the Multimatic 220 AC/DC. Hobart gives 9,500 watts continuous on 240V for the Handler 210i. Hobart does not recommend the Handler 140EZ on engine-driven welders or standalone generators at all.

None of the makers lists shielding gas in the box, so budget for a cylinder.

FAQ

Who owns Hobart welders?

Hobart Welding Products is an ITW Welding company. Hobart’s spec sheets call it “An ITW Welding Company” and state that Hobart and the Hobart logo are trademarks of Illinois Tool Works, Inc. Miller Electric Mfg. LLC carries the same “An ITW Welding Company” line on its spec sheets, so Miller and Hobart are sister brands under one parent. Lincoln Electric is a separate company, founded in Cleveland, Ohio, in 1895.

Are Hobart and Miller welders the same?

No. They share a parent company, ITW, but they are sold as separate lines with their own model names, features and warranties. Some small parts cross over: Hobart lists its .023 in. contact tip (770174) as fitting both Handler and Millermatic welders. The machines differ. The Millermatic 211 PRO lists Auto-Set and pulsed MIG, which the Handler 210i does not list, and Miller’s warranty is three years parts and labor where Hobart uses its 5/3/1 terms.

Is Hobart a good welder brand?

On the makers’ own figures, Hobart’s Handler 210i is the lightest and lowest-listed of the three dual-voltage MIG picks on this page: it weighs 26 lb and Hobart lists it at about $1,000. Its 5/3/1 warranty runs five years on transformers, stabilizers and main rectifiers. Where Hobart falls behind is duty cycle on 120V, and Hobart’s current welder line lists no AC TIG machine.