The Best Home Welding Shop Kit, Item by Item

A garage welding shop needs about a dozen things before the first bead: a welder that runs on the circuit you have, protection for eyes, hands, body and lungs, a steel surface to work on, ways to hold parts, a grinder, and an extinguisher within reach. Each job below gets one pick, chosen on the maker’s published figures.

Welder: Hobart Handler 140EZ for a 120-volt garage

The Hobart Handler 140EZ is the welder to buy for a garage with ordinary 120-volt outlets. Hobart rates it at 30 to 140 amps, 90 amps at a 30% duty cycle, and 24 gauge up to 3/16 in mild steel in a single pass. It ships with the gun, a dual-gauge regulator and a built-in gas solenoid, so it runs flux-core wire on day one and solid wire under gas once you add a cylinder.

Get Hobart Handler 140EZ

The reasons it suits a first shop are in Hobart’s literature. EZ Mode sets the machine from two knobs, material thickness and wire diameter, and a manual mode with infinite voltage control is there when you want to fine-tune the arc. The Quick Select drive roll has three grooves: two for .024 in and .030/.035 in solid wire and one for .030/.035 in flux-cored wire. The spool hub takes 4 in and 8 in spools. The machine is spool gun ready for aluminum with Hobart’s SpoolRunner 150, with no extra interface box. It weighs 53 lb, carries Hobart’s 5/3/1 warranty (five years on the transformer and main rectifier, three on the PC boards and drive system, one on the gun), and Hobart’s spec sheet says it draws 20 amps at rated output on 115 volts. That last figure decides the circuit: Hobart’s manual says a 20 or 30 amp individual branch circuit protected by time-delay fuses or a circuit breaker is required, and allows an extension cord of at most 25 ft in 14 AWG or 50 ft in 12 AWG. Hobart also states that it is not recommended for engine-driven welders or standalone generators. Hobart’s manual defines the 30% duty cycle as 3 minutes of welding and 7 of rest in every 10 minutes at 90 amps; if the unit overheats, output stops and Hobart says to wait 15 minutes for it to cool and reduce amperage or duty cycle before welding again. It gives an operating range of 14 to 104°F, with output derated above 104°F, says wearers of pacemakers and other implanted medical devices should keep away and consult their doctor and the device manufacturer first, and carries a California Proposition 65 warning that the product can expose you to chemicals including lead. For other 120-volt and dual-voltage machines, see best MIG welders for beginners.

Who should buy something else: if the garage already has a 240-volt outlet, or you plan to build trailers and heavy frames, the Hobart Handler 210i is the better buy. It is dual-voltage, 120V/240V, with a 30 to 210 amp range. Hobart rates it at 210 amps at a 25% duty cycle on 240 volts and 24 gauge to 3/8 in mild steel, and it weighs 26 lb. Hobart lists it at about $1,000. It also runs from a generator: Hobart states full output from a generator providing 9,500 continuous and 11,000 peak watts. Hobart says output will be limited with smaller generators. The voltage choice is set out in 110V vs 220V welders.

Get Hobart Handler 210i

Helmet: Lincoln Electric Viking 3350

The helmet is the piece of kit you look through for every second of arc time, so it is chosen on optics and switching. Lincoln documents the Lincoln Electric Viking 3350 (K3034-4) with a 1/25,000 second light-to-dark switching speed, four arc sensors, a variable shade of 5 to 13, and a 1/1/1/1 optical clarity rating. The viewing area is 12.5 sq in (3.74 x 3.34 in), large enough to see the joint and the surrounding work when you are fitting parts. A home shop runs MIG, flux-core, often stick and sometimes TIG. Lincoln rates the filter for TIG down to 2 amps AC or DC, so the helmet still darkens if you take up low-amp TIG later.

Get Lincoln Electric Viking 3350

Two smaller features matter in a garage. The low-profile grind button on the outside of the shell switches between weld and grind modes (Lincoln’s spec sheet says to press and hold it for 3 seconds), which is useful because you go from tacking to grinding many times on every project. The helmet runs on a replaceable CR2450 battery with solar assist, takes Lincoln’s magnifying cheater lenses, uses Lincoln’s X6 headgear and weighs 22 oz. Lincoln lists ANSI Z87.1 and CSA Z94.3 compliance. Lincoln says not to use the helmet without the correct clear cover lenses installed on both sides of the auto-darkening cartridge, gives an operating range of 14 to 131°F (-10 to +55°C), and its product page carries a California Proposition 65 cancer and reproductive harm warning. Lower-priced options are compared in best welding helmets under $100, and the wider field in best welding helmets.

Gloves: Tillman 50 for MIG and flux-core

MIG and flux-core gloves are a trade-off between heat protection and the feel you need for the gun trigger. Tillman builds the Tillman 50 from premium top grain cowhide with split cowhide reinforcement in the palm, the back of the fingers and the thumb strap, and lines it with fleece for heat protection. It has a seamless index finger for trigger feel, a wing thumb for gripping the gun, an elastic back, a 4 in split cowhide cuff and DuPont Kevlar stitching throughout. Sizes run from small to 2X. Tillman’s spec sheet says to inspect the gloves before each use and remove them from service if there is any evidence of damage or excessive wear, warns that they are cut-resistant, not cut proof, and carries a California Proposition 65 warning that they can expose you to hexavalent chromium, known to the State of California to cause cancer and birth defects or other reproductive harm.

Get Tillman 50

Who should buy something else: a fleece-lined MIG glove is too thick for TIG, where you feed filler rod by hand. If TIG becomes your main process, add a thin unlined TIG glove and keep the Tillman 50 for MIG, flux-core and grinding. The choices by process are in best welding gloves.

Jacket: Tillman 9230 FR cotton with cowhide sleeves

In a home shop most spatter lands on the forearms and the front of the body, especially in flat and horizontal welding at the table. The Tillman 9230 puts leather where the spatter lands and keeps the rest light. The torso is royal blue 9 oz, 100% cotton Westex FR7A flame-resistant fabric, which Tillman states meets ASTM D6413-10, the test used for the ASTM F1506 pass/fail limit of a 6 in maximum char length. The sleeves are side split cowhide sewn with Kevlar thread, with a soapstone pocket on each sleeve and an inside pocket. The length is 30 in (a 36 in version is sold as the 9230-36), and sizes run from small to 6X.

Get Tillman 9230

Tillman designs it for light-duty welding only, which describes most garage MIG and flux-core work. If you run long stick or flux-core sessions out of position or overhead, buy a full leather jacket instead. Tillman’s care instruction is to take it to a dry cleaner experienced with leather, so do not put it in the washer. Tillman’s page also carries a California Proposition 65 warning that the jacket can expose you to chemicals including hexavalent chromium, known to the State of California to cause cancer and birth defects or other reproductive harm. Other options are in best welding jackets.

Respirator: Miller LPR-100 Gen. II under the helmet

A garage does not clear welding fume as quickly as a shop with forced extraction. The plume rises from the joint straight into the space under your helmet. The Miller LPR-100 Gen. II Half Mask Respirator is designed to fit under a welding helmet. It has a downward-facing exhaust valve to cut heat buildup and lens fogging, and a low-profile shape that does not interfere with safety glasses. Miller rates its P100 filters at 99.97% filtration of airborne particles and aerosols, oil-based and non-oil-based, including metal fumes. A wrap-around spark guard protects the filter media. It is NIOSH-certified under 42 CFR part 84 with an assigned protection factor of 10, comes with two P100 filters, and Miller lists it at about $42.

Get Miller LPR-100 Gen. II

Buy the 294962 for a medium or large face and the 294961 for a small or medium face. Replacement filters are sold in pairs: the 294963 P100 filters, or the 294964 P100 with nuisance organic vapor relief if the smell of hot paint or oil bothers you; Miller says those filters are designed for organic vapor concentrations not exceeding OSHA’s permissible exposure limits or other applicable government exposure limits, whichever is lower. Miller classes it as a tight-fitting respirator, so it only seals on a clean-shaven face; OSHA’s respirator standard bars facial hair where the mask seals. Miller builds in a fit-check exhaust valve for the daily check before you start. Miller states that fit testing is required for mandatory use, and builds in a sample port for it. Other respirators and powered air systems are compared in best welding respirators.

Ventilation and fume extraction: what to buy and what to skip

Ventilation moves fume and gases out of the garage; the respirator filters the particle fume that reaches your face. Its P100 filters do not remove gases such as ozone, nitrogen oxides or carbon monoxide, so the respirator never replaces ventilation. At minimum, open the large door and set a fan to one side of you, so the air moves across the work from side to side toward the opening and carries the plume away from your face. A fan directly behind or in front of you can pull fume into your breathing zone instead. Do not aim the fan at the arc itself, because a strong draft blows the shielding gas away from a MIG weld and causes porosity. Flux-core wire does not need a cylinder but produces more fume, so it needs more air movement, not less.

What is not worth the money for a home shop is an industrial fume extraction cabinet. Miller’s FILTAIR SWX-D, for example, is a cabinet unit with an 8 in extraction arm. Miller’s spec sheet lists the cabinet alone at 130 lb, and a welding supply listing prices it at about $8,200. That is built for production booths. For occasional garage welding on clean mild steel, the respirator plus cross-ventilation is the practical setup, and portable source-capture units are compared in best welding fume extractors for anyone who welds galvanized or coated steel often. Hobart’s welder manual says to wear an approved air-supplied respirator if ventilation is poor, and not to weld galvanized, lead- or cadmium-plated steel unless the coating is removed from the weld area, the area is well ventilated and you wear an air-supplied respirator.

Table: Miller ArcStation 30FX for a shared garage

A welding table needs to be steel, flat and clampable, and in a garage that also holds a car it needs to move and fold away. The Miller ArcStation 30FX does all of that. It has a 30 x 30 in solid steel top, 3/16 in thick, with an X-pattern for clamping, plus wheels, a handle and a fold-up design. Miller lists it at 35 in high and 74 lb, with a removable gun holder, and Miller’s own clamp for the slots is part number 300613. Miller lists it at about $710.

Get Miller ArcStation 30FX

Who should buy something else: if the garage has a dedicated corner and you weld every week, a heavier fixture table with a hole grid is the better long-term buy. The other route is to build a table from square tubing and 1/4 in plate as your first project with the welder, which takes longer but costs less. Both routes are compared in best welding tables.

Cart: Hobart Running Gear/Cylinder Rack 194776

Once you add shielding gas, the cylinder has to stand upright and stay secured, and the welder should move with it. Hobart’s Running Gear/Cylinder Rack 194776 is the cart Hobart lists as an accessory for both the Handler 140EZ and the Handler 210i. Hobart states that it accepts gas bottles up to 7 in in diameter and 33 in tall, with a 75 lb maximum. It measures 18 in high, 30 in long and 12.5 in wide, rolls on four wheels, and has a 12.5 x 19.75 in welder shelf. Assembly is required.

Get Hobart 194776 Running Gear Cylinder Rack

The 7 in diameter limit is the figure to check against your gas supplier’s cylinders before you choose a size. Hobart’s manual for the cart says an oversized cylinder can tip it, to always secure the cylinder (the cart comes with a 24 in chain), to secure or remove any tools stored on the cart before moving it, never to lift the cart with the welder and cylinder on it (use the handles), and not to overload the handles with cables (10 to 15 ft cables at most). It also carries a California Proposition 65 cancer and reproductive harm warning. Larger cylinders, and carts with drawers for wire and tools, are compared in best welding carts.

Magnets: Strong Hand Tools Adjust-O MSA46-HD

Magnet squares hold two pieces at a fixed angle while you tack them. The Strong Hand Tools Adjust-O MSA46-HD is chosen for one documented feature: it switches. Strong Hand gives it an on/off switch with a mid-point position, so you can slide the part into alignment with the magnet partly on, then switch it fully on to hold, and turn it off to lift it away and clean off the spatter. Strong Hand describes the Adjust-O line as holding work at 30°/60°, 45° and 90°. Strong Hand rates the MSA46-HD at a 90 lb maximum pull force, measured on the longest side against 3/8 in steel, with rare earth magnets in a fully enclosed double-plate body. It measures 4.4 x 3.8 x 1.1 in and weighs 1.5 lb. Buy two, so that both sides of a frame corner are held square.

Get Strong Hand Tools Adjust-O MSA46-HD

Strong Hand’s own limits are worth following exactly. The magnets are for tack welding only, and you remove them before completing the weld. Avoid prolonged exposure to heat sources of 175°F (80°C) and above. More magnet types are compared in best welding magnets.

Clamps: Strong Hand Tools PR115S locking C-clamps

Every project needs clamps that lock with one hand and do not slip as the part heats. The Strong Hand Tools PR115S is an 11 in locking C-clamp with a 3.3 in throat depth, a 4.0 in maximum clamping capacity and swivel pads that Strong Hand says give a secure grip on round workpieces without damaging the surface. Strong Hand makes it from forged, heat-treated steel with nickel and chrome plating. The 4 in capacity is the figure that matters: it clamps 2 in tube to the table top with room to spare. Strong Hand sells it as a three-pack (PR115S-3BDK) for about $84 with a one-year limited warranty.

Get Strong Hand Tools PR115S

Add plain C-clamps and a bench vise as projects demand. Specialist welding clamps are compared in best welding clamps.

Grinder: DeWalt DWE402

After the welder, the angle grinder is the most-used tool in the shop. It cuts stock, bevels joints, takes mill scale off before welding and dresses the bead afterwards. The DeWalt DWE402 is a 4-1/2 in corded grinder with an 11 amp motor and a no-load speed of 11,000 RPM. The safety feature that decides it is the paddle switch with a lock-off lever, which DeWalt designs to prevent accidental start-up: you push the lever back, then squeeze the paddle, and the grinder runs while the paddle is held. It also has a lock-on button for long surface grinding, released by pressing and letting go of the paddle. DeWalt adds auto-off brushes, a one-touch guard that rotates 360 degrees, tool-free wheel release, and a 3-year limited warranty with 1 year of free service.

Get DeWalt DWE402

DeWalt’s manual sets two rules. First, every wheel or disc must be rated for at least the maximum speed marked on the tool, which is 11,000 RPM here. Second, the grinder comes with a Type 27 guard for grinding, and DeWalt requires a closed, two-sided guard when you cut with abrasive cut-off wheels. Buy the Type 1 cutting guard before you use cut-off wheels. The manual also requires safety goggles or safety glasses with side shields and a full face shield compliant with ANSI Z87.1 for the operator and anyone within 50 ft, says to always use the side handle, not to operate the grinder near flammable materials, to run a new wheel for one minute in a protected area with no one in line with it, to depress and release the paddle once before plugging in so a locked-on switch cannot start the tool unexpectedly, and to limit daily time of use because vibration can cause permanent injury to fingers, hands and arms. It warns that grinding dust can contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm, and to use NIOSH/OSHA-approved respiratory protection appropriate for the dust exposure. Cordless and higher-power grinders are compared in best angle grinders for welding.

Fire extinguisher: Amerex B402

Welding and grinding throw sparks into a room that usually holds cardboard, rags, a lawnmower and a gas can, so the extinguisher has to handle ordinary combustibles and flammable liquids. The Amerex B402 is a 5 lb ABC dry chemical extinguisher with a UL rating of 3A:40B:C. Amerex’s own 5 lb B500 and B424 carry 2A:10B:C, so the B402 carries the higher A and B ratings from the same 5 lb cylinder. Amerex builds it with a drawn-steel cylinder, a stored pressure design and a chrome-plated brass valve body with a stainless steel handle and lever. Amerex rates it from -65°F to 120°F, which covers an unheated garage, and backs it with a 6-year warranty. It is made in Trussville, Alabama.

Get Amerex B402

Mount it on the wall by the door, not behind the welding table. That way you reach it on the way out, never by going past the fire. Amerex’s manual says to hang it with the top no more than 5 ft above the floor, inspect it monthly, never test-discharge it, start at least 8 ft back from a fire, evacuate and ventilate the area once the fire is out, and recharge it immediately after any use. After your last weld, keep checking the shop for at least an hour, because sparks can smolder in sawdust and cardboard long after the arc is off.

Buying order on a tight budget

If the whole kit cannot be bought at once, buy in the order the risks arrive. The welder, helmet, gloves, respirator and extinguisher come first, because you cannot weld safely without any of them. The jacket follows quickly, since an FR jacket covers the shirt underneath, and a spark can set an ordinary shirt alight. The grinder comes next, because you will need to cut and clean metal before your first real project. Magnets and clamps follow as soon as you start fitting parts together. The table and cart can wait: a first project can be a welding table built with the Handler 140EZ itself, and the cylinder can be chained to a wall until the cart arrives.

Setting up the space

The home welding shop setup guide covers the room itself: welding shop layout by workflow zone, circuits, floors, lighting and the hazards to clear. The points that shape this kit are short. Keep a clear path to the door. Clear wood, cardboard, paint and fuel from the area sparks can reach: Hobart’s welder manual says to remove all flammables within 35 ft (10.7 m) of the arc, or tightly cover them with approved covers if that is not possible. Never weld near brake cleaner or degreaser vapor, because some contain chlorinated solvents that the arc’s ultraviolet light breaks down into toxic gases. If others use the garage while you weld, a curtain stops arc flash from reaching them; options are in best welding curtains and screens.

These picks were not tested; this is what the makers’ specifications and documentation show for each item.

FAQ

Can the Hobart Handler 140EZ run on a normal garage outlet?

It is a 120-volt welder, but Hobart’s spec sheet lists a 20 amp input draw at its rated output of 90 amps, so give it a 20 amp circuit that nothing else is running on. Hobart’s manual says a 20 or 30 amp individual branch circuit protected by time-delay fuses or a circuit breaker is required. Hobart also states that the 140EZ is not recommended for use with engine-driven welders or standalone generators.

Do I still need the respirator if the garage door is open?

Yes. An open door and a fan move fume out of the room, but the plume rises straight from the weld into the space under your helmet. The Miller LPR-100 Gen. II sits under the helmet and filters what you breathe there; Miller rates its P100 filters at 99.97% filtration of airborne particles, including metal fumes. Ventilation and the respirator do different jobs, and a garage shop needs both.

Why buy the Amerex B402 instead of a cheaper 5 lb extinguisher?

Weight is not the rating. Amerex’s own 5 lb B500 and B424 carry a UL rating of 2A:10B:C, while the 5 lb B402 carries 3A:40B:C. The B402 carries the higher A and B ratings from the same size cylinder, and a welding shop has both ordinary combustibles and flammable liquids nearby.